潛水攪拌機，攪拌機中的機，1. 運輸和使用注意事項

Precautions for transportation and use.

1.1 決不允許用潛水泵攪拌機的電纜起吊或懸掛潛水攪拌機。在搬運或懸掛潛水攪拌機時，可用帶鉤的鏈條鉤在起吊板上。

The cable of the submerged mixer is never permitted to be used to lift or hang the mixer. While the submerged mixer is being moved or hanged, the chain with a hook can be hooked on the lifting board.

1.2 如果潛水攪拌機仍在使用或浸在水中，在0℃以下的氣溫時，可以繼續使用。

        The submerged mixer still in use or immersed in water can be used as usual under 0℃.

1.3 潛水攪拌機使用油脂或潤滑油進行潤滑。由于密封磨損，油脂或潤滑油會漏出。這時，請趕快將潛水攪拌機送至本廠維修部或委托維修點，更換密封，以免將電機燒壞。

      Grease or lubricant shall be used for lubrication of the submerged mixer. Once the grease or lubricant leaks for the wear of the seal, please send the mixer to the service department or the commissioned service stations of the manufacturer to change the seal lest the electric motor is burnt out.

1.4 未切斷電源時，不得移動潛水攪拌機，人不得進入水中。

      Before the power is cut off, the submerged mixer shall not be moved, nor is anyone allowed to go into the water.

1.5 潛水攪拌機安裝以后，不能長期浸在水中不用，建議每半個月至少運行4個小時以檢查其功能和適應性，或提起放在干燥處備用。

      The submerged mixer, having been erected, shall not be immersed in water when it is not used for a long time. It is suggested that the mixer shall be operated for at least 4 hours per month to check its function and adaptability or lifted in the dry place for future use.

1.6 潛水攪拌機必須保證安全接地。

       Safe grounding of the submerged mixer shall be ensured.

2. 作用說明

Directions

在潛水攪拌機啟動之前，應有一名合格的電工對該系統進行檢查，確保采取下述各項所要求的電器保護措施。

Before the submerged mixer is started, a qualified electrician should check the system, ensuring that the protective measures required as follows are adopted.

2.1 潛水攪拌機在運行前，應用0-500V兆歐表檢查電機定子繞組對地絕緣電阻，低不得低于1兆歐。

      Before operation of the mixer, a 0.500v megohmmeter should be used to examine the insulance against ground of the stator winding of the electric motor which should never be lower than 1 megohm.

2.2 電源電壓一定要在銘牌上標出的額定電壓±5%的范圍內，電源電壓升高值不得超過額定電壓的10%，如果電源離潛水攪拌機使用的距離較遠時，電纜的截面積應當加粗，接頭應盡可能少些，否則會使電壓下降的過大，且結頭處應密封防水。

      The power voltage should be within 5% higher or lower than the rated voltage marked on the data plate, and the power voltage should increase by less than 10% of the rated one. If the electric power is relatively far away from the site where the submerged mixer is used, the section of the cable should be widened and the connections smaller in quantity with seal for resistance of water. Otherwise, the voltage will decrease too greatly.

2.3 電纜中，帶標志▼為接地線，一般為黃綠線，為保證安全，必須將地線接牢并比其他線長出50mm。

      The wire of the cable with the mark of ▼ is the ground wire, usually in yellowish green. The ground wire should be fastened and 50mm longer than any other wire for the sake of safety.

2.4 檢查葉輪旋轉方向。

Check the rotation direction of the impellers.

使用三相電源的潛水攪拌機，在潛水攪拌機初次啟動和每次重新安裝后都應檢查轉動方向，轉動方向不正確，會降低效率，并損壞潛水攪拌機。

     For the submerged mixers using three-phase electric power, before their first working and after each reinstallation, the rotation direction of the impellers should be examined. If they rotate in the wrong direction, the efficiency will be reduced and the mixers damaged.

檢查方法為，潛水攪拌機在終安裝前，面對葉輪方向，葉輪為逆時針旋轉，如果幾臺潛水攪拌機連在一個控制器上，各臺潛水攪拌機必須單獨進行檢查，如果旋轉方向不正確，可以調換控制器上三相線中的任意兩條線的位置，就能改變旋轉方向。

      Means of examination: Before the installation is completed, standing in front of the mixer facing the impeller, one should find that the impeller is rotation in the counterclockwise direction. If several mixers are connected to the same control device, each should be examined separay. If the impellers rotate in the wrong direction, exchange the places of any two wires on the three-phase control device.

維修保養說明

Directions for Maintenance

潛水攪拌機產品可靠，性能優良。每臺在出廠前，都認真的進行了終檢驗。*潤滑的滾珠軸承使潛水攪拌機具有大的耐久性，然而，為了保證潛水攪拌機的使用壽命，建議進行定期的檢查和保養。

The submerged mixers are in good quality, which have all been subjected to careful final test. Life-time lubricated ball bearings enable the mixers to stand maximum wear and tear. However, regular examination and maintenance is still recommended to guarantee the service life the mixers.

若與我廠訂有維修保養合同的，維修部在任何情況下都可以提供好的業務性維修。

If the service contract is signed with the manufacturer, the service department can provide the best professional service under any circumstances:

1. 注油和換油

Oiling and Reoiling

潛水攪拌機的油室在出廠前，已注入適量潤滑油。該油應每年進行更換。

Before the submerged mixers leave the factory, the oil rooms have been injected with adequate lubricant, which should be changed each year.

換油應按下列方法進行：

Reoiling should be conducted according to the following directions.

把潛水攪拌機放置好，使油室油塞朝下，擰松螺塞，放出潤滑油，然后用洗滌油清洗油室，再注入適量的潤滑油，換一個新的O型圈，將螺塞旋緊。

Place the mixer steadily in the direction which renders the oil room stopper downward, unscrew the stopper, let out the lubricant, clean the oil room with washing oil, inject right amount of lubricant, change a new O-shaped ring, and tighten the stopper.

如果油中發現有水，換油后三個星期以后必須重新檢查一次，如果油又變成乳液狀，機械密封件應進行檢查，必要時應更換。（與我廠維修部）

If water is found in the lubricant, it should be checked again three weeks after reoiling. If the lubricant gets milk like again, check the mechanical seal component, and change it if necessary. （Contact the service department of the manufacturer.）

如自己更換密封，需做氣密封實驗。

If you change the seal component yourself, hermetic seal experiment is necessary.

注：油為變壓器油。

Note: the oil should be transformer oil.

2. 運轉故障

Operation Failure

萬一運轉發生故障，不能確定原因，不可采用臨時湊合的方法，也不要私自亂修亂拆。（與我廠檢修部）

If any undetermined failure occurs, putting up with it is undesirable, so is foolish repairing and dismantling without permission. （Contact the service department of the manufacturer）.